How To Get Flarp Out of Carpet – 4 Quick Steps

The kid always loves cool playthings, and flarp is one of a few perfect toys that can entertain them at home. Yet, this sticky stuff often causes a lot of trouble and annoys you, as it is likely to stick on the ground, clothes, and even your new beautiful carpet!  

If you have a headache trying to get the flarp out from your carpet, do not rush, or you will destroy the mat! Let’s learn how to get flarp out of carpet correctly with our guidelines. Read on for details!

Flarp can get stuck in your carpet frequently (source)

How To Get Flarp Out of Carpet? 4 Detailed Steps 

Even though flarp is a beneficial and creative toy for kids of all ages, it could be a terrible disaster to remove if being stuck inside the carpet.

With these four easy steps and techniques below, you will know how to get flarp out of the carpet and leave your rug spotless without damage quickly!

Step 1: Test The Effectiveness On A Small Area 

First of all, it is better to test the effectiveness of the adhesive remover or carpet cleaner on your carpet, as each type of carpet will react distinctively. 

Choose a small spot at the corner where the substance is stuck and test the result. Specifically, it is essential to help you avoid the stains for the whole rug and potential problems occurring if the carpet’s material is difficult to work on. 

Step 2: Chill The Flarp 

Once the small test is successful, the next step is to chill the flarp. An ice cube is an ideal solution for freezing the sticky substance on the stained area. In particular, take a cube and scrub it against the putty until the flarp gets hard. You can easily pick away the hardened flarp with this method. 

In case your carpet has a particularly deep pile, the use of tweezers is also a great way to pluck it away! Moreover, do not forget to use a plastic bag for wrapping and avoid leakage while freezing.

You can use ice cubes to remove the adhesive substance.

Step 3: Scrape Off The Flarp 

The next stage in the procedure is to rub the sticky material as much as you can. To make it easier, use a butter knife, a gentle scraper, and your fingers to pluck the hardened flarp off the carpet fibers. Also, gently flush away and do not scrape too deep to avoid destroying your carpet’s fiber.

This step will be sufficient if you do the job correctly. But sometimes, based on our experience, the most common problem that happens is the left behind stain that requires more treatment. Let’s move to the next step to see how many solutions you can use for wider stains!

Step 4: Treat The Stain 

There are many means you can apply to remove the stains remaining on the carpet. You may simply utilize one of the following products to protect your rug’s fabric:

Use Rubbing Alcohol

A cotton ball saturated in a generous amount of rubbing alcohol is an easy and cheap tool to remove any silly leftover putty. In particular, blot the flarp with the wet ball by gentle pressure. Remember to switch to the new cotton ball each time it becomes soiled with the flarp. Then, keep repeating until there are no stains or traces of flarp remaining on the carpet.

If you are out of rubbing alcohol, white household vinegar, baking soda, or even vodka are also good alternatives.

Rubbing alcohol is also a great way to treat stains. (source)

Use Water Solution

Soaking a piece of white cloth with cool water is also a great method to take that stubborn flarp out. To get it done, gently rub the last remnants of putty with the damp rag to ensure no residue is left behind the deeper area.

Once you have flushed away from the last pieces of flarp, use a dry rag to soak up any excess water and leave the carpet to air dry.

Use Solvent Solution

In case rubbing alcohol, cool water, and cotton balls are not efficient methods to get rid of any stains leftover from the removed flarp, it is time to bring out a stronger solution – oil-based solvent.

The use of an oil-based solvent is the best choice to take out any stains from the rug. At this stage, be sure to test it on a small spot first to see if any adverse reaction occurs. 

If nothing happens, you can spray it directly on the carpet. Wait for five to ten minutes, then take a wet cloth to clean the area gently. Then you must repeat this procedure until the trace has been removed entirely. Then, blot any excess moisture with a dry clean cloth to finish.  

Use WD-40

Besides oil-based solvent, we also want to recommend you the WD-40. One of the potential advantages is that the oil in WD-40 will loosen the attachment of sticky putty to the rug’s fabric. Subsequently, it becomes easier to get out the stain.

WD-40 (source)

Add More Putty

Undeniably, it is quite weird if we advise you to add more silly putty on top of the stains to remove its trace, right? In fact, this technique is based on the logical thinking that the new putty will stick to the old parts. Thus, when you use other treatments to remove the stain, the combo of old and new putty, which have been stuck together, can be removed easier.

Though this is a cool way to apply, we consider that this is not the safest method. Let’s do the job with the freezing and scraping ways first!

The Bottom Line 

Flarp is fun to play with, but it will turn to tears soon if it gets stuck to your fancy carpet. But does it need to be as difficult as it seems? The answer is no! With suitable techniques and correct products, the silly putty is removed more effectively than you think.  

Hopefully, with the above solutions, you now know how to get flarp out of carpet and make your favorite rug look clean back as you expect. 

Thank you for your reading, and see you in the next blog!

Leave a Comment

Your email address will not be published. Required fields are marked *